A rapid drying, clear sealer for new, unfinished wood. It's ease of sanding and excellent hold-out qualities make it the ideal first-coat sealer for both satin and gloss finishing systems. It has been specifically formulated for use under Eventone Urethane Varnish, Eventone Varnish Stain and Eventone Spar Varnish.

Eventone Sanding Sealer is not recommended as a sealer coat for floors, exterior application, liquid plastics, including Eventone Poly-Dax. Eventone Sanding Sealer may be used under Eventone Urethane Varnish (0395 Gloss and 0399 Satin) but should not be used under other brands of polyurethane varnish.

The surface should be clean, dry and free of all contaminants. New wood should be sanded smooth and dust removed with a lint free cloth or tack rag. Always sand with the grain. Previously finished wood should be stripped down to bare wood completely, using paint and varnish remover. Follow manufacturer's instructions and warnings for proper use of paint and varnish remover. Proceed as with new wood.

If desired, stain wood with Eventone Stain. For the smoothest appearance, fill opened-grained woods such as Oak, Mahogany and Walnut with wood filler tinted to the shade of the stain. Allow to dry overnight and apply one coat of Sanding Sealer.

Remove old wax, oil and dirt from surface to be finished with a strong detergent solution and wipe surface clean using mineral spirits. Allow to dry. If surface is hard and slick, sand thoroughly to dull surface for maximum adhesion of topcoat. Remove sanding dust with tack rag. If sealed, apply one coat of Sanding Sealer and allow to dry 1 hour. Sand sealer lightly, remove dust and apply finish coat of clear varnish or Sanding Sealer.

If the old wood is badly scarred and in poor condition, remove the old finish either by sanding or with stripper and finish as new wood.

Stir before use and periodically during use to assure uniform sheen. Do not shake as air bubbles may be entrapped in the sealer. Sanding Sealer is packaged at brushing consistence. Apply at package viscosity.

Apply a full brush coat of Sanding Sealer liberally and smoothly using a clean, good quality brush. To spray, use the following recommendations or equal:

AIRLESS SPRAY:

Tip . . . . . . . . . . . . . . . .011-.013"

Fan . . . . . . . . . . . . . . 40° -60° (8-12 inch fan)

Pressure . . . . . . . . . . 1200-1600 PSI

Clean brushes and equipment with mineral spirits or V.M.&P. Naphtha. Dispose of used stain and waste in accordance with local, state and federal regulations.

Eventone Sanding Sealer will cover approximately 450 square feet per gallon (41 square meters per 3.785 liters) on smooth surface. Rough surfaces will require more material. Add 10% when figuring requirements for loss and wastage. Approximate dry mil thickness of 0.9 mils at recommended spreading rate of 450 square feet per gallon on smooth surface.

Optimum drying conditions are 60° F. to 90° F. (16° C. to 32° C.) at 50% R.H.

To Sand . . . . . . . . . . . 1 to 1 1/2 Hours

To Recoat . . . . . . . . . . . . . . 2 Hours

Eventone Urethane Varnishes, Varnish Stains and Spar Varnish are recommended as topcoats.

Weight Gallon: 7.05

Weight Solids: 35.9%

Volume Solids: 28.4%

Coverage:

@ 1 Dry Mil: 455 sq. ft./gallon

@ Spread Rate: 400 sq. ft./gallon (4.0 mils wet)

Deposits a 1.1 mil dry film

VOC (g/l): 542

Viscosity: 45-55 Sec. #4 Ford Cup @ 77° F.

Gloss @ 60: 35-45

Grind (Hegman): #6

DOT Class: Flammable, Flash Point 57° F., UN1263

Federal Specification: N/A

HMIS/NFPA: 1,3,0

Cure Time (Based on 70° F. & 50% R.H.):

To Touch: 30 Minutes

To Recoat: 2 Hours

Recommended Thinner: None. Apply at package viscosity. Mineral spirits for clean-up.

Temperature Resistance: Continuous 150° F., Intermittent 200° F.

HEALTH CAUTIONS! Keep away from heat and open flame. Avoid prolonged contact with skin and breathing of vapor or spray mist. Do not take internally. Close container after each use. Use only with adequate ventilation. KEEP OUT OF THE REACH OF CHILDREN. For specific safety requirements, refer to the Material Safety Data Sheet.

LIMITATION OF LIABILITY: To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance, but is subject to change without prior notice. We make no guarantee of any kind, express or implied, including merchantability and fitness for particular purposes. Liability, if any, is limited to replacement of the product or refund of the purchase price. Labor, or cost of labor, and other consequential damages are hereby excluded.