EVENTONE LIQUID PLASTIC 6-6 0605
CLEAR WOOD FINISH
DESCRIPTION:
Eventone Liquid Plastic is an extremely durable, flexible, alcohol and abrasion resistant polyurethane clear finish for interior or exterior use. Eventone Liquid Plastic Gloss is excellent for interior or exterior unfinished wood surfaces. Eventone Liquid Plastic Satin is for use on interior finished or unfinished wood surfaces such as floors, paneling and kitchen cabinets. Brush application is recommended, however, product may also be applied by spray.
The surface should be clean, dry and free of all contaminants. New wood should be sanded smooth and dust removed with a lint free cloth or tack rag. Always sand with the grain. Previously finished wood should be stripped down to bare wood completely, using paint and varnish remover. Follow manufacturer's instructions and warnings for proper use of paint and varnish remover. Proceed as with new wood.
NATURAL UNFILLED WOOD - Apply two or three coats of urethane varnish. Allow each coat to dry at least 12 hours, but no longer than 48 hours. Avoid heavy coats. Sand between coats and remove sanding dust.
STAINED WOOD - For beautiful wood color effects, stain wood with wiping stain and allow to dry overnight. Apply two coats of urethane varnish. Allow each coat to dry at least 12 hours, but no longer than 48 hours. Avoid heavy coats. Sand between coats and remove sanding dust.
STAINED FILLED WOOD - Opened-grained wood such as oak, walnut and mahogany may be filled with wood filler, either tinted to match the color of stain or untinted, or natural effect. Apply sanding sealer and allow to dry overnight, sand lightly for maximum smoothness. Remove sanding dust and apply urethane varnish. If a second coat of urethane varnish is required, allow first coat to dry at least 12 hours, but no longer than 48 hours. Sand lightly and remove sanding dust before recoating. If no filler is to be used on opened-grained wood, and on closed-grained wood such as fir, pine and birch, omit sanding sealer.
Remove old wax, oil and dirt from surface to be refinished with a strong detergent solution, then wash with mineral spirits. Allow to dry and sand thoroughly to dull surface for maximum adhesion. Remove sanding dust with a tack rag. Apply one or more coats of urethane varnish. Allow each coat to dry at least 12 hours, but no longer than 48 hours, and sand lightly before recoating.
Old varnish in poor condition should be removed either by sanding or with commercial stripper, following label directions. Finish as for unfinished surface.
FLOORS:
NEW FLOORS - Sand smooth. APPLY EVENTONE LIQUID PLASTIC TO BARE, UNFILLED FLOORS ONLY. Reduce first coat with one pint of mineral spirits to each gallon of urethane varnish. Allow to dry at least 12 hours, but no longer than 48 hours. Sand lightly and remove sanding dust. Apply second coat of urethane varnish without reduction. The longer the final coat is allowed to dry before traffic is allowed, the harder and more mar resistant the finish.
OLD FLOORS - Remove finish to bare wood and finish as shown under "New Floors" above.
5/99
Stir satin varnish before use and periodically during use to insure even sheen of finish coat. The most common complaint about any satin varnish is variation in sheen caused by insufficient or total lack of stirring.
When applying by spray, or using as seal coat on unfinished wood, one pint of mineral spirits should be added to each gallon urethane varnish.
Apply with a clean good quality brush, or by spray using the following recommendations as a guide. Avoid heavy coats.
AIRLESS SPRAY:
Tip . . . . . . . . . . . . . . . .011-.013"
Fan . . . . . . . . . 40° -60° (8-12 inch fan)
Pressure . . . . . . . . . . . 1200-1600 PSI
Clean brushes with mineral spirits or V.M.&P. Naphtha. Dispose of used varnish and waste in accordance with local, state and federal regulations.
Eventone Liquid Plastic will cover approximately 500 square feet per gallon (47 square meters per 3.785 liters) on smooth surface. Approximate dry mil thickness of 1.1 mil at recommended spreading rate of 500 square feet per gallon. Rough surface will require more material. Add 10% when figuring material requirements for loss and wastage.
Optimum drying conditions are 60° F. to 90° F. (16° C. to 32° C.) at 50% R.H.
Dust Free . . . . . . . . . . . 30-60 Minutes
To Handle . . . . . . . . . . . . . . 4 Hours
To Recoat . . . . . . . . . . . . . Overnight
5/99
EVENTONE LIQUID PLASTIC
CLEAR WOOD FINISH
Values based on Eventone Liquid Plastic Clear Wood Finish, 0605
Weight Gallon: 7.50
Weight Solids: 43.2%
Volume Solids: 34.5%
Coverage:
@ 1 Dry Mil: 553 sq. ft./gallon
@ Spread Rate: 400 sq. ft./gallon (4.0 mils wet)
Deposits a 1.4 mil dry film
VOC (g/l): 510
Viscosity: 30-40 Sec. #4FC @ 77° F.
Gloss @ 60: 25-35
Grind (Hegman): #7
DOT Class: Combustible, Flash Point 103° F.
Federal Specification: TT-C-540 Performance Alternate
HMIS/NFPA: 1,2,0
Cure Time (Based on 70° F. & 50% R.H.):
To Touch: 4 Hours
To Recoat: Overnight
Recommended Thinner: Mineral spirits for clean-up and VM&P Naphtha for reduction to spray
Temperature Resistance: Continuous 150° F., Intermittent 200° F.
HEALTH CAUTIONS! Keep away from heat and open flame. Avoid prolonged contact with skin and breathing of vapor or spray mist. Do not take internally. Close container after each use. Use only with adequate ventilation. KEEP OUT OF THE REACH OF CHILDREN. For specific safety requirements, refer to the Material Safety Data Sheet.
LIMITATION OF LIABILITY: To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance, but is subject to change without prior notice. We make no guarantee of any kind, express or implied, including merchantability and fitness for particular purposes. Liability, if any, is limited to replacement of the product or refund of the purchase price. Labor, or cost of labor, and other consequential damages are hereby excluded.
4/92
5/99
| Home | Products | Surface Prep | Paint Estimator |
| MSDS | Articles | Contact Us |